maintenance your home

How to fix water leaks from pipes A)   Disconnect all power to the spa. Inspect the equipment compartment. If leak is under the pump, this indicates a possible pump seal failure. If leak is detected, replace pump or install new seal, as appropriate. B)   Check all union fittings at hot tub pump and heater.  Unions can even vibrate loose on a brand new spa during shipment, and should be hand tightened if necessary.  If hand tightening is difficult, loosen pump mounting bolts, move components into alignment, then tighten unions and re-tighten pump mounting bolts.  Never use a wrench to tighten spa unions. C)   Next, inspect heater, pressure switch and surrounding components. Replace any defective parts as indicated by leak.  See   Heater Testing D)   Inspect all of the valves. Repair or replace if leak is indicated. Knife style valves are sometimes bolted together and contain a gasket between the halves which can fail, particularly...

Maintain a Water Heater Perform routine maintenance on your water heater every six months to insure proper functionality and prolonged use. Planning Both gas and electric water heaters have a safety device called a pressure relief valve. In the event the tank overpressurizes, the relief valve opens and releases the pressure. If the valve doesn't operate correctly, the tank can overpressurize and explode. To check the pressure valve: Step 1 Turn off the electricity to the water heater or turn the gas switch to pilot. Step 2 Shut off the cold-water inlet to the water heater. Step 3 Position the bucket to catch water from the pressure relief valve. Step 4 Pull the trip lever on the valve. You should hear a slight rush of air or see some water and vapor exit through the pressure relief valve. If you don't, drain the tank and replace the valve. Flush the Tank Every Six Months Sediment buildup in the tank can reduce your ...

The first problem : cooker Blacks and any Dirty utensils You should clean the burners regularly and preferably being developed in I E (water + vinegar + kirosen) then boiled and dried well Note ........ If burners (burners of the wet Bay means Blacks pots so kept them dry The second problem : Ergonomics primers but not all burners? At a fraction on Button primers (metal head) Make sure of the quality of if endowed head primers tested if Ergonomics and does not near screwdriver railing of head primers Primers and press the ignition button will notice spark transmitted to the screwdriver and watch must The separation stuck Screwdriver Ok if the Cherz and the torch does not catch him what is the solution? Set copper primers mode If that does not work? Keep the small piece of sanding and paw the front part of the head of the metal to ignite in primers and totally head  metal, primers

How to replace a toilet seat When a toilet seat is worn out it can make for uncomfortable use. When a toilet seat is broken though, it can be dangerous to sit on, so should be replaced immediately. Fortunately, changing a toilet seat is one of the easiest repair jobs you can do in a bathroom - and has the potential to add a whole new look to your toilet. Replacing a toilet seat is almost as simple as unbolting it and then bolting another on in its place. Buy a new toilet seat The first step is to buy your new toilet seat. Since most toilets are rounded, you should have no problems finding one that fits and suits the rest of your bathroom, though if you have an elongated bowl, this may be a little trickier to do as you will need a different shaped seat. There are all sorts of different toilet seats available, so if you're feeling like a change of scenery this would be a very good opportunity to make a bit of a change! Remove the old toilet seat Next, check th...

 how i do maintenance bathroom Regular   bathroom maintenance   is an essential part of housekeeping. Over the long run, this will save you a considerable amount of money as well, because you can avoid problems related to plumbing, leaks, mold and mildew. Some easy, but important tips for regular bathroom maintenance are listed below. 1 – Ensure that the Grout and Sealant are Intact The grout and sealant around the tiles over a bathtub or in a shower cubicle require frequent inspection. Due to the constant exposure to heat, humidity and moisture, the grout often wears off or cracks. Make sure that the grout is intact and free from mold or mildew. To clean mold, mildew or grout stains, use oxygen bleach. If you find any evidence of missing grout, you must clean the area, dry it and apply new grout. 2 – Look for Leaking Spouts or Pipes Leaks around a pipe or spout must be remedied as soon as they are spotted. If left unattended, they could progressively become wor...

Refrigerator maintenance Check thermostats : 1. Bring Thermostat refrigerator 2. Using Alawmmitr then examine the parties connected thermostats 3. If gave Alawmmitr the signal be Althemustat the conductor 4. Turn the cylinder of Freon, and open and shed on the root of coolant thermostats 5. Examine the ends of thermostats: • If you gave the signal to be thermostats continued Atlan • If you do not give a signal be thermostats separator (ergonomics) Examination Rilah: 1. Using Alawmmitr then scans the parties L, M: • If you do not give referring be Rilah to the Atlan and replaces 2. Using Alawmmitr then scans the parties L, S: • In the normal position of the relay must not give a signal • Turn Rilah and examine the parties to the case did not give referring be Rilah to the Atlan and replaces Examination Alawvrlod : 1. Do bring Alawvrlod and preheat the metal plate and then inspect both sides Alawvrlod using Alawmmitr: • in the event gave the signal have conductive...

  Refrigerator breakdowns and ways to fix it Refrigerators exposed to a lot of problems and faults and because the presence of the refrigerator is indispensable for any home of homes, especially in the summer and that the refrigerators of the multiple functions and very important to this dealt with in this article some of the faults that may be exposed to the icebox 1 - some faults may occur in the refrigerator because of a cut in the wire which reach Altaymr the May be a problem only in cutting Balslak or may be Altaymr the need to change and are discovered through a test run after changing the wires and we will discover if there McCann problem in Altaymr that or not 2 - there is no damage in key Cab leading to the high temperature of the cab or fall dramatically and are being treated by changing the key and a test of experimentation 3 - there has been some damage in the thermostat, which leads to the high temperature of the freezer and this happens for several reasons, may be ...